Product ID:PLASTIC STEEL PUTTY (A) RESIN
MSDS Date:04/21/1992
FSC:8030
NIIN:00-903-6545
Kit Part:Y
MSDS Number: BWDZG

Emergency Phone: 508-777-1100/800-424-9300(CHEMTREC)

Info Phone: 508-777-1100

Cage: 0RZG3

Telephone: 215-855-8450

Cage: 20420

BISPHENOL A-EPICHLOROHYDRIN COPOLYMER

CAS: 25068-38-6

RTECS: SL6475000

Fraction By Weight: 10-30% %

NON-HAZARDOUS INGREDIENTS

Fraction By Weight: BALANCE

LD50 LC50 Mixture:ORAL LD50 (RAT): 11400 MG/KG-EPOXY RESIN
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:MAY BE MILDLY IRRITATING TO THE EYES.
METAL FILLER PARTICLES COULD SCRATCH CORNEA. SKIN CONTACT MAY CAUSE
MINIMAL TO MILD IRRITATION IN MOST PEOPLE. APPROXIMATELY 1% OF
WORKERS MAY BECOME SENSITIZED B Y TOO MUCH SKIN CONTACT WITH EPOXY
RESINS; ITCHING, SWELLING, OR RASHES MAY THEN RESULT FROM FURTHER
CONTACT.
Explanation of Carcinogenicity:THIS COMPOUND CONTAINS NO INGREDIENTS AT
CONCENTRATIONS OF 0.1% OR GREATER THAT ARE CARCINOGENS OR SUSPECT
CARCINOGENS.
Effects of Overexposure:EYE IRRITATION, SKIN IRRITATION, ITCHING,
SWELLING OF SKIN, RASHES.
Medical Cond Aggravated by Exposure:PRE-EXISTING ALLERGIES, ECZEMA,
SKIN DISORDERS MAY BE AGGRAVATED BY EXPOSURE TO THIS PRODUCT.

First Aid:EYES: FLUSH WITH WATER FOR 15 MINUTES WHILE HOLDING EYELIDS
OPEN. GET MEDICAL ATTENTION. SKIN: REMOVE CONTAMINATED CLOTHING.
WASH WITH SOAP AND WATER. IF IRRITATION PERSISTS, GET MEDICAL
ATTENTION. IN HALATION: REMOVE TO FRESH AIR. RESTORE BREATHING. GET
MEDICAL ATTENTION. INGESTION: DO NOT INDUCE VOMITING. DILUTE WITH
TWO GLASSES OF WATER. GET MEDICAL ATTENTION.

Flash Point Method:PMCC
Flash Point:>400F,>204C
Lower Limits:NOT GIVEN
Upper Limits:NOT GIVEN
Extinguishing Media:FOAM, DRY CHEMICAL, CARBON DIOXIDE
Fire Fighting Procedures:FIRE FIGHTERS SHOULD USE NIOSH APPROVED SCBA &
FULL PROTECTIVE EQUIPMENT WHEN FIGHTING CHEMICAL FIRE.
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.

Spill Release Procedures:PREVENT SKIN CONTACT. SCRAPE UP AND DISCARD IN
SUITABLE CONTAINERS, USING INERT ABSORBENT MATERIAL SUCH AS
VERMICULIT IF NEEDED. WASH SPILL AREA WITH AN INDUSTRIAL CLEANING
AGENT. IF SOLVENT IS USED, TAKE CARE AGAINST OVEREXPOSURE AND
FIRE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE IN A COOL, DRY PLACE WITH
ADEQUATE VENTILATION. KEEP AWAY FROM OPEN FLAMES AND HIGH
TEMPERATURES. AFGTER MIXING WITH HARDENER, OBSERVE PRECAUTIN
Other Precautions:AVOID SKIN CONTACT. LAUNDER CONTAMINATED CLOTHING
BEFORE REUSE. LEATHER ARTICLES SUCH AS SHOES AND BELTS CANNOT BE
DECONTAMINATED AND SHOULD BE DISCARDED. WHEN SANDING OR MACHINING
THE CURED MATERIAL, TAKE PROPER PRECAUTIONS AGAINST DUST.

Respiratory Protection:NOT NORMALLY REQUIRED.
Ventilation:LOCAL EXHAUST AND MECHANICAL (GENERAL) VENTILATION TO
MAINTAIN EXPOSURE LEVELS.
Protective Gloves:RUBBER
Eye Protection:SAFETY GLASSES OR GOGGLES
Other Protective Equipment:PROTECTIVE CLOTHING AS REQUIRED TO AVOID
SKIN CONTACT. AN EMERGENCY EYE WASH STATION AND SHOWER SHOULD BE
AVAILABLE.
Work Hygienic Practices:WASH WITH SOAP AND WATER AFTER HANDLING PRODUCT
AND BEFORE EATING DRINKING OR SMOKING.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

HCC:N1
Boiling Pt:B.P. Text:NOT GIVEN
Melt/Freeze Pt:M.P/F.P Text:NOT GIVEN
Vapor Pres:NIL
Vapor Density:> 1
Spec Gravity:2.8
pH:7.0
Evaporation Rate & Reference:<<1 (BUTYL ACETATE = 1)
Solubility in Water:NIL
Appearance and Odor:DARK GREY PASTE WITH LITTLE ODOR
Percent Volatiles by Volume:O %

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, ACIDS, BASES
Stability Condition to Avoid:EXTREME HEAT, OPEN FLAME
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE,
ALDEHYDES AND ACIDS FROM INCOMPLETE COMBUSTION
Conditions to Avoid Polymerization:HEAT IS RELEASED WHEN THIS RESIN IS
MIXED WITH EPOXY HARDENER. USE CAUTION WHEN MIXING A POUND OR MORE.

Waste Disposal Methods:PREVENT WASTE FROM CONTAMINATING SURROUNDING
ENVIRONMENT. DISCARD ANY PRODUCT, RESIDUE, DISPOSAL CONTAINER OR
LINER IN ACCORDANCE WITH ALL FEDERAL, STATE AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.